Skip to content

How To Clear Descale Message On Keurig Duo

Descaling is an important process that removes built-up minerals from your Keurig® brewer. A descale message will appear on your brewer’s display when it is time to descale. To clear the message, simply follow the descaling instructions in your Owner’s Manual.

6 Steps to Clear Descale Message On Keurig Duo

If your Keurig® brewer is displaying a descale message, it is time to descale your brewer. Descaling is an important part of cleaning your Keurig® brewer. This process removes built-up calcium deposits, or scale, that can impact your brewer’s performance over time.

It is important to learn how to clear the descale message on Keurig duo because this message indicates that the machine needs to be descaled. This process helps to clean and maintain the machine, and it is important to do this on a regular basis to ensure that the machine is working properly.

Step 1: Stepbystep Guide

If your Keurig® brewer is displaying a descale message, it is time to descale your brewer. Descaling should be done every 3-6 months, or more frequently if you notice a decrease in brewing performance. This step-by-step guide will walk you through the descaling process so you can get back to enjoying your favorite beverages.

Step 2: Clear Descale Message On Keurig Duo

To clear the descale message on your Keurig Duo, follow these steps: 1. Press and hold the Power button for 3 seconds. 2. Select the Settings icon. 3. Select Maintenance. 4. Select Clear Descaling Message. 5. Press the Power button to confirm.

Step 3: Use Descaling Solution

Descaling is an important process that helps to remove built-up calcium and other minerals from your Keurig® brewer. The Keurig® Descaling Solution is designed specifically for use with Keurig® brewers. To use, simply mix the entire bottle of solution with water and follow the instructions in your brewer manual. After completing the descaling process, be sure to run a few brewing cycles with plain water to remove any residual solution.

Step 4: Remove Water Filters

To remove the water filters, first locate them on the sides of the water reservoir. There are typically two filters, one on each side. Grasp each filter firmly and twist it counterclockwise until it comes loose. Once the filters are removed, throw them away and insert new ones.

Step 5: Run Full Brew Cycle With Vinegar

Run a full brew cycle using only water and 1/2 cup of white vinegar. After the brew cycle is complete, discard the water and vinegar. Run another full brew cycle using only fresh water to rinse the system.

Step 6: Rinse Thoroughly

Rinse thoroughly means to remove all traces of the cleaner from the outside and inside of the machine. This can be done by running water through the machine several times.


Frequently Asked Questions

How Do I Reset My Keurig Duo After Descaling?

The process for resetting your Keurig duo after descaling is as follows: 1) Press and hold the power button for 5 seconds. 2) Release the power button and then press it again. 3) When the display shows “RESET” press and hold the power button for 3 seconds. 4) Your Keurig duo is now reset and ready to use.

How Do I Clear The Descale Message On My Keurig?

Descale your Keurig at least once every 3-6 months, or sooner if you notice a change in the taste of your coffee. To descale, simply follow the on-screen instructions or the descaling guide in your Owner’s Manual.

Why Won’T My Descale Light Go Off On My Keurig?

There are a few possible reasons for this: -The water reservoir is not full -The filter needs to be replaced -There is built up scale in the machine

How Do You Reset A Keurig Slim After Descaling?

To reset a Keurig Slim after descaling, unplug the machine and then plug it back in.

To Review

To clear the descale message on a Keurig Duo, users should first remove the water reservoir and locate the small white descale cap on the bottom of the reservoir. They should then use a pin or paper clip to remove the cap and pour in white vinegar until the reservoir is full. Users should then replace the descale cap and reattach the water reservoir to the brewer. Next, they should press the power button to turn on the brewer and wait for it to start dripping. Once it does, they should let it run for two full cycles or until the descale message disappears.

Leave a Reply

Your email address will not be published. Required fields are marked *